Topic: Xenon Diagram For Lpt Flashing (Read 1390 times)

drogy · « **Reply #465 on:** December 26, 2009, 07:29:00 AM »

Hey guys! I'm having some trouble with a LPC-H2148. i followed this tutorial: http://forums.xbox-scene.com/index.php?sho...493&st=150#. now i got to the point where flashmagic gets a deviceid, i can read and erase the flash but when i get to the programming part i get an error - "failed to send data to the device". i've been at it for hours and i'm just about to give up. what i've noticed now, after erasing the flash, is that i only get the red power led on the lpc-2148 when i connect the device to usb even after removing the bridge. i'm a little worried i might have somehow damaged the device because i switched the rx-tx to get it to work in flashmagic. also, my rs232 board has a switch on it that says "run" and "program". i've tried both and still no luck. any ideeas?

hazed69 · « **Reply #466 on:** December 26, 2009, 10:17:00 PM »

what version of window do we need to have for this to work?

Antman1 · « **Reply #467 on:** December 27, 2009, 03:58:00 AM »

I have seen people with win98 make this work so windows98 and up.

hazed69 · « **Reply #468 on:** December 27, 2009, 10:47:00 AM »

wonder why its not working for me i have win7 32
ive done everything listed and still i cant get it to work in dos
i type C: nandpro20 nandpro.exe lpt: -r16 nandbackup1.bin
it does nothing ive check my wires make sure they are making contact
i checked bois setting for spp thats good but im stuck
any help would be great thanks
i do have a xenon board no hdmi and dash of 7373 i belive

hazed69 · « **Reply #469 on:** December 27, 2009, 03:28:00 PM »

well i fig it now
needed to change the dir to c:\
i was showing c:\documennts~1\xbox
now its c:\
c:\nandpro lpt: -r16 nand1.bin
it shows me that the the test its doing
at the end it says "could not detect a flash controller"?
what am i doing wrong?

brando56894 · « **Reply #470 on:** December 27, 2009, 06:17:00 PM »

it could be numerous things, check this thread for ideas. Apparently the LPT reader sucks and about 25-50% of the people that use it cant get it to work (including me). I have a USB reader on the way but wanted to get a head start on it.

hazed69 · « **Reply #471 on:** December 27, 2009, 09:13:00 PM »

HA HA YES i got it to work didnt use the five
100 ohms
and did a lil resoldering again make sure the were connected
Now once i made sure my BIn file i just got are exactly alike
i can go ahead and flash my drive with the hacked.bin i just got right ?

hazed69 · « **Reply #472 on:** December 27, 2009, 10:19:00 PM »

well i checked them both look good
i flashed it GOOD
but now e79 error 1033
dammit so close and the door closes on me
anyone can help with this?

Antman1 · « **Reply #473 on:** December 28, 2009, 04:04:00 AM »

what board do you have? also did you leave the jumper wires in place? And make sure the JTag cable is not hooked to your PC when trying it.

hazed69 · « **Reply #474 on:** December 28, 2009, 03:15:00 PM »

Does the hacked bin I download like xenon 1921 does that need to be open and my CPU key and maybe other info needs to injected to it RIGHT! Antman I just reflashed back to orig.bin but I'm starting to think the hack .bin needs something

thehump2001 · « **Reply #475 on:** January 05, 2010, 06:36:00 PM »

Noob question: Can I use my USB to DB9 cable instead of a LPT to USB deal?

foolkiller · « **Reply #476 on:** January 06, 2010, 05:45:00 AM »

QUOTE(thehump2001 @ Jan 5 2010, 08:36 PM)

Noob question: Can I use my USB to DB9 cable instead of a LPT to USB deal?

Sorry don'think so.

CamaroGuy · « **Reply #477 on:** January 07, 2010, 08:25:00 PM »

does wire gauge matter? and if so whats a good gauge to use?

craz3d · « **Reply #478 on:** January 07, 2010, 08:28:00 PM »

Wire gauge does matter. A lot of people recommend 30 gauge, but I personally used the individual braided wires from a length of CAT-5E cable. There are 4 twisted pairs of 24 gauge wire inside, which leaves you with one extra wire as a spare in case you mess up. 24 gauge is slightly thicker than 30 but you can still solder the points without issue.

CamaroGuy · « **Reply #479 on:** January 07, 2010, 08:31:00 PM »

QUOTE(craz3d @ Jan 7 2010, 10:28 PM)

Wire gauge does matter. A lot of people recommend 30 gauge, but I personally used the individual braided wires from a length of CAT-5E cable. There are 4 twisted pairs of 24 gauge wire inside, which leaves you with one extra wire as a spare in case you mess up. 24 gauge is slightly thicker than 30 but you can still solder the points without issue.

fantastic thanks alot man i just happen to have a spool of 30 gauge wire from installing my wii modchip so i'm gonna do this tonight so I can uncripple my banned box and then homebrew one of my other RROD repairs that haven't been online in almost 2 years

Author Topic: Xenon Diagram For Lpt Flashing (Read 1390 times)