Topic: Warning Serial Data Is Bad (Read 44 times)

ianbborg · « **on:** February 03, 2020, 08:05:00 AM »

Hi Guys I think I have a huge problem here, I Connected everything to the ck3 pro and then I realized that I didn't have, so i improvised and did some modification to the power cable, but i have mistakenly switched the connector upside down;/ lol there was a bit of a small fire to tell you the truth and there are some burnt power slot stun there. But anyways I tried to connect it again, this time in the right position and it turned on, does this mean there was no damage ? I continued to try to extract the Key but I keep getting this message "Warning Serial Data is Bad" do you have any suggestions?
Thankss

turny · « **Reply #1 on:** April 11, 2009, 06:32:00 PM »

QUOTE(ianbborg @ Apr 11 2009, 04:05 PM)

Hi Guys I think I have a huge problem here, I Connected everything to the ck3 pro and then I realized that I didn't have, so i improvised and did some modification to the power cable, but i have mistakenly switched the connector upside down;/ lol there was a bit of a small fire to tell you the truth and there are some burnt power slot stun there. But anyways I tried to connect it again, this time in the right position and it turned on, does this mean there was no damage ? I continued to try to extract the Key but I keep getting this message "Warning Serial Data is Bad" do you have any suggestions?
Thankss

yes but you wont like it
if you havent extracted your firmware you are screwed, the best suggestions are try and sell the bits you got left over on e**y and be more careful in the future.Sorry to be so blunt.

ianbborg · « **Reply #2 on:** February 04, 2020, 02:41:00 AM »

Oh thanks I knew I had screwed up but anyways. Thanks for your reply and if I buy a new dvd rom that would be ok would it? and what would be the best choice? maybe benq?

Thanks again

turny · « **Reply #3 on:** April 12, 2009, 04:22:00 AM »

QUOTE(ianbborg @ Apr 12 2009, 10:41 AM)

Oh thanks I knew I had screwed up but anyways. Thanks for your reply and if I buy a new dvd rom that would be ok would it? and what would be the best choice? maybe benq?

Thanks again

unless you can get your key from drive , a new drive would not work , drive keys can only be extracted from the drive and yours is toast, sorry

ianbborg · « **Reply #4 on:** February 04, 2020, 04:26:00 AM »

Oh shoot didn't know that, But I think that i really screwed nothing up on the pcb since there was no etching or solder where there is a hole now and there is power trough the CK3 altough I tried connecting it to the xbox and the drive didn't want to come out but maybe I did something wrong there. The thing is that the drive is powering up when hooked with the pc and it is being recognized. Maybe I should try doing it with serial cable or Dosflash? But I really don't know how to do that so if you have a tutorial link or something I would really appreciate. Yesterday I tried booting into dos from a cd since I don't know why but I cannot seem to boot from a usb with iprep. But I cannot access the pendrive from the dos when booted from CD;/

This post has been edited by ianbborg: Today, 12:27 PM

turny · « **Reply #5 on:** February 04, 2020, 04:50:00 AM »

if you put it in the xbox and it will not eject then your firmware is fried , hundreds maybe thousands of ppl have done exactly the same thing as you, its easy to do cos when you are using a probe or spear you are working upside down,you dont even have to plug it in fully just touching the pins will do damage,try and search the forums for a answer.

woody21_1 · « **Reply #6 on:** February 04, 2020, 11:25:00 AM »

have you checked the pcb in the liteon drive for any damage? if theres something burned you may be able to repair it extract the keys at least.
if the drives not working in the console anymore then check the drive pcb.

you could try a new ck3, sounds like you have fried the max232 chip on it hence the error saying serial data is bad.

This post has been edited by woody21_1: Today, 07:29 PM

Gr3Ml!N · « **Reply #7 on:** April 12, 2009, 02:17:00 PM »

the same thing happened to me, i almost fried my drive too, luckly i was able to get the key first, and thank god it didnt damage my drive.

ianbborg · « **Reply #8 on:** April 12, 2009, 02:23:00 PM »

Hey I just tried to connect the dvd to the Xbox and this time when i pressed the button it Opened:D does this mean the drive is still ok??

Gr3Ml!N · « **Reply #9 on:** April 12, 2009, 02:31:00 PM »

QUOTE(ianbborg @ Apr 12 2009, 01:59 PM)

Hey I just tried to connect the dvd to the Xbox and this time when i pressed the button it Opened:D does this mean the drive is still ok??

possibly.

ianbborg · « **Reply #10 on:** April 12, 2009, 02:39:00 PM »

What can I do to check it out? maybe insert a movie or something since i have no original games here?

Gr3Ml!N · « **Reply #11 on:** April 12, 2009, 02:48:00 PM »

QUOTE(ianbborg @ Apr 12 2009, 02:15 PM)

What can I do to check it out? maybe insert a movie or something since i have no original games here?

yeah do that, and i would suggest trying to get the key first. lol u got ck3, i got a serial to usb adapter for 6$ lol. and it worked flawlessly.

ianbborg · « **Reply #12 on:** April 12, 2009, 02:50:00 PM »

Wait, can someone tell me whats the correct procedure for my situation please.
Currently I am
1. turning off computer
2. Connecting CK3 to power
3. Connect ck3 power to Lite-ON
4. Connect LiteOn to Pc's intel Sata controller using a Sata Cable
5. Turn On Ck3 Pro and eject drive with CK3 switch.
6. Turn Off CK3
7. Manually turn the drive half way in.
8. Turn On pc and boot into windows xp
9. Turn on CK3 with Blue light and with DIY Probe in r707 circle hole
10 Dvdkey32 try to extract.

Note: now i have tried to do it with usb connected but its not working and its chip its getting extremely hot and I have tried to connect the ck3 with the serial cable to my pc but nothing happens.

I really don't know what to do, if anyone has any solution i would reaaly appreciate

Gr3Ml!N · « **Reply #13 on:** April 12, 2009, 02:55:00 PM »

QUOTE(ianbborg @ Apr 12 2009, 02:26 PM)

Wait, can someone tell me whats the correct procedure for my situation please.
Currently I am
1. turning off computer
2. Connecting CK3 to power
3. Connect ck3 power to Lite-ON
4. Connect LiteOn to Pc's intel Sata controller using a Sata Cable
5. Turn On Ck3 Pro and eject drive with CK3 switch.
6. Turn Off CK3
7. Manually turn the drive half way in.
8. Turn On pc and boot into windows xp
9. Turn on CK3 with Blue light and with DIY Probe in r707 circle hole
10 Dvdkey32 try to extract.

Note: now i have tried to do it with usb connected but its not working and its chip its getting extremely hot and I have tried to connect the ck3 with the serial cable to my pc but nothing happens.

I really don't know what to do, if anyone has any solution i would reaaly appreciate

ok, heres a tutorial
http://team-xecuter....eon_windows.htm

Gr3Ml!N · « **Reply #14 on:** April 12, 2009, 03:53:00 PM »

QUOTE(ianbborg @ Apr 12 2009, 02:45 PM)

Ok the drive played a dvd

now Maybe I connected the Diy probe in a wrong way or the r707 isnt working on the pcb?

you probably connected it wrong way. and i think you have selected the wrong com port.

Author Topic: Warning Serial Data Is Bad (Read 44 times)