Print

[Sottilde]

Alright, here goes.  The computer I have hooked up to my xbox has two NICs - one running to the xbox, at 192.168.1.1 (xbox is 192.168.1.3), and another NIC on DHCP (usually ends up at 192.168.0.2) over to my server machine, which is 192.168.0.1.  

I'm getting the message about the ports not being forwarded.  I have checked my server and everything seems fine.  Both machines are running WinXP Home, and the server is using ICS.  I set up two port forwards at 34518 and 34519 UDP on the server machine(I set 34518/34519 for both internal and external requests).  Everything seems to check out.  I ran Xtest:

[3:47:09 PM] X-Link configuration inspection begins..

[3:47:09 PM] Attempting Socket Bindings..
[3:47:09 PM] Attempting X-Link Data Stream Bind (34518 UDP)..
[3:47:09 PM] Attempting X-Link Data Stream Bind (34518 UDP)..
[3:47:09 PM] Attempting XBConnect Hosting Stream Bind (8602 UDP)..

[3:47:09 PM] Attempting Port Loobpack Tests..
[3:47:10 PM] 34518 -> OK (192.168.1.1)
[3:47:10 PM] 34519 -> OK (192.168.1.1)
[3:47:10 PM] 8602 -> OK (192.168.1.1)

[3:47:10 PM] Initialising WinPCap control layer..

[3:47:10 PM] Enumerating WinPCap NICs:
[3:47:10 PM] Broadcom iLine10™ Network Adapter (MS's Packet Scheduler) - DeviceNPF_{5E572FF1-74A6-4178-8589-2CD0C095EEBF}
[3:47:10 PM] ADMtek AN983 NDIS5 Driver (MS's Packet Scheduler) - DeviceNPF_{5EE3BC00-6183-4B05-9377-58255C317CAA}

[3:47:10 PM] Checking IsGood status of NICs:
[3:47:10 PM] Broadcom iLine10™ Network Adapter (MS's Packet Scheduler) =  1
[3:47:10 PM] ADMtek AN983 NDIS5 Driver (MS's Packet Scheduler) =  1

[3:47:10 PM] Attempting Promiscuous Control:
[3:47:10 PM] Broadcom iLine10™ Network Adapter (MS's Packet Scheduler) - STARTED
[3:47:10 PM] Broadcom iLine10™ Network Adapter (MS's Packet Scheduler) - STOPPED
[3:47:11 PM] ADMtek AN983 NDIS5 Driver (MS's Packet Scheduler) - STARTED
[3:47:11 PM] ADMtek AN983 NDIS5 Driver (MS's Packet Scheduler) - STOPPED

[3:47:11 PM] MAC Capturing:
[3:47:11 PM] Listening 5 seconds on Broadcom iLine10™ Network Adapter (MS's Packet Scheduler)
[3:47:16 PM] Listening 5 seconds on ADMtek AN983 NDIS5 Driver (MS's Packet Scheduler)

[3:47:21 PM] UPnP Enumeration (WAIT):
[3:47:25 PM] UPnP Init failed.. skipping enumeration..

[3:47:25 PM] XServer External Test:
[3:47:25 PM] Sending request..
[3:47:25 PM] Waiting 5 seconds for reply..
[3:47:25 PM] XServer accepted connection..
[3:47:25 PM] Server -> Sent 3 test packets to 68.114.251.69 - HTTP response was 68.114.251.69 , full was

[3:47:30 PM] Tests complete... post in the forum if you need to.

Everything seems to check out there, as well.  I tried putting my IP in my profile, checking safe mode in Xlink, and nothing seems to do it.  I'm located in midwestern U.S., so I doubt the NTL issues would be any problem.  I had this problem a few months ago and it seemed to fix itself after a while (didn't change any settings) but I soon after forgot about Xlink and now it's broken again.

Any ideas?

Thanks,
Sottilde

EDIT: And yes, I do have v2.2.4 RC2.

[jz28]

not sure mate, but i would recommend using a hub instead of having 2 subnets there like that...

[Sottilde]

I have a bit of an odd setup.  Between my server and my main computer, I use a phoneline (10mbps) connection, requiring no hub and nothing but two $10 phoneline network cards.  I find it handy that I don't have to run cables.  Then, I simply have a hub and a network cable going to my xbox, which is right near my main computer.

Still have not gotten it to work... this has been a big problem for me and any fixes you would know of would help greatly.

Thanks,

Sottilde

[Sottilde]

Sottilde