Topic: X2.2 Help... (Read 96 times)

thomes08 · « **on:** July 20, 2003, 01:58:00 PM »

OK, i'm modding my friends box and i soldered a x2.2 lite in. I used my programmer to flash the chip, that went well. It erased, wrote, then verified.... When i put the chip into his xbox and start it up, it turns on and off, and on the third time it stays on but i have no picture. When i turn the chip off everything works fine. I thought it may have been my soldering, so to check that i took out my x2lite chip that i've had working for a few months and put it in his xbox using the same cable with the 9 wires soldered to his box.... (just switched chips) and everything works just fine with my chip in there. Oh by the way before i used the programmer i turned it on to see if it worked, and it fragged 3 times then started normally with the cromwell bios. i just didn't want to deal with getting the thomson drive to read cd-rw's and i dont want to waste a dvd-r on a 1 mb file. DOes anyone have any help here?!?!?!
thanks so much

thomes08

swiss · « **Reply #1 on:** July 20, 2003, 02:03:00 PM »

im having the same problem. on xbins help they told me it was a bad flash, i did it trough dvd so they told me to get the programmer. if you find anything else about it pm me .

thomes08 · « **Reply #2 on:** July 20, 2003, 02:10:00 PM »

he has a version 1.0 if that helps any, swiss what version do you have.

thomes08

thomes08 · « **Reply #3 on:** July 20, 2003, 02:18:00 PM »

oh, also you know how it comes with that small cable within with the 2 wires comming out. similar to the cable with the 9 wires comming out. but it only has the d0 and the ground wire... i didn't use that on my chip, so i assumed i dont have to on his. am i correct with this assumption? what does that do anyways.

thomes08

swiss · « **Reply #4 on:** July 20, 2003, 06:27:00 PM »

version 1.0 and i also solderd all the color cables dont know whats wrong but im having the same problem. and you assumed right

thomes08 · « **Reply #5 on:** July 20, 2003, 11:42:00 PM »

yes i know my soldering is correct because when i put my chip in his xbox using the same wires i installed on his xbox it works fine.... i dunno what's goin on here

thomes08

musical_mercenary_420 · « **Reply #6 on:** July 20, 2003, 11:46:00 PM »

QUOTE

--------------------------------------------------------------------------------
oh, also you know how it comes with that small cable within with the 2 wires comming out. similar to the cable with the 9 wires comming out. but it only has the d0 and the ground wire... i didn't use that on my chip, so i assumed i dont have to on his. am i correct with this assumption? what does that do anyways.

that is for soldering the lil pins that came with your x2lite.....insted of the wires

i had this problem b4 when i was flashing oxzflash but fixed it with the programmer ......

try reflashing the chip

thomes08 · « **Reply #7 on:** July 21, 2003, 02:46:00 AM »

i have tried about 10 times ti reflash it, each time with x2 4977, i'm going to try an older version i think..... so confused
thomes08

thomes08 · « **Reply #8 on:** July 21, 2003, 02:48:00 AM »

but the weird thing is even before i used the programmer when i booted it up to see if the cromwell bios would run it fragged twice and on the third time ran, then i turned it off and tried again and couldn't get it to boot, then tried again and it would frag then boot...

thomes08

poiygon · « **Reply #9 on:** July 21, 2003, 10:33:00 AM »

Why not boot the xbox with the x2 lite, switch it with the x2 pro, and use FlashX to reprogram it.

thomes08 · « **Reply #10 on:** July 21, 2003, 12:33:00 PM »

i dont have an x2 pro, i just tried hot swapping it and his chip wouldn't flash at all (yes the flash bios was on unprotect) it just froze and i lert it sit about 15 minutes (i did this on my machine) and i had no other choice but to turn it off and now my system wont work at all it just gives me an error 5
any help cause i think i may be really fucked!!

thomes08

Author Topic: X2.2 Help... (Read 96 times)