Topic: 1.5 And 1.3 Winbond W49f020t-90b (Read 159 times)

A@ron · « **Reply #30 on:** December 28, 2003, 06:38:00 AM »

I think the 0x0900 is what you get when your points are not bridged properly, someone want to confirm this?

A@ron

lordvader129 · « **Reply #31 on:** December 28, 2003, 10:05:00 AM »

yeah, 0x0900 means the chip isnt write enabled

did you say you bridged 2 points on teh bottom? cuz both points you need to bridge are on the top of the motherboard

iLLNESS · « **Reply #32 on:** December 28, 2003, 08:59:00 AM »

theres 3 points u gotta solder proly

most people say its only 2 because the 3rd works only if uve soldered one of the 2 bad but i think thats bs.. im not an amateur solderer and i had to do 3 points

it all depends on the chip ur using and winbonds u do

PsiDOC · « **Reply #33 on:** December 28, 2003, 12:19:00 PM »

CHECK YOUR SOLDER POINTS!!!!!!!!!!!!!
Detects, then freezes on erase = Naffed up Write enable jumpers!
Nuff Said.
Psi

RaysMD · « **Reply #34 on:** December 28, 2003, 02:37:00 PM »

yea, I've done a 1.3 with the same winbond chip. Just download raincoat .501 from #xbins, and you don't need this stupid line.

QUOTE

Flash = 0x0900,"Winbond - W49F020T",0x40000

MAKE sure your soldering is good. You only need to solder the top 2 points. Flashing winbond chips only works with raincoat, no evoX.

rays

ftothe3 · « **Reply #35 on:** December 28, 2003, 03:03:00 PM »

i have a v.1.5 with this winbond chip and i flashed it with raincoat and got the same error message that you did. the problem was my soldering. i fixed that up and it flashed perfectly.

Reznik Akime · « **Reply #36 on:** December 28, 2003, 05:29:00 PM »

Is there anyway to run raincoat via the audio or dashboard explot to flash that bothersome chip besides the gamesave methood?

A@ron · « **Reply #37 on:** December 28, 2003, 08:02:00 PM »

if you do the audio exploit couldnt you run evolution x and then flash your tsop that way?

A@ron

Reznik Akime · « **Reply #38 on:** December 28, 2003, 08:18:00 PM »

Nope. Evox cant flash the 90b.

Zedek · « **Reply #39 on:** December 29, 2003, 05:11:00 AM »

Evox can't flash winbond chips PERIOD

ftothe3 · « **Reply #40 on:** December 29, 2003, 09:11:00 AM »

i did it with the audio exploit too. this is what i did: copy all the files from the 000000000000 directory of the 007savewithraincoat.zip file onto the E: drive of the xbox. then, goto dos box and type xbedump default.xbe -audio. then, rename out.xbe to linux.xbe and put that in your E: drive. Then, when you run the audio exploit (do the button combo) it will load up raincoat and u can telnet in and flash.

Reznik Akime · « **Reply #41 on:** December 29, 2003, 10:03:00 AM »

Ohh.. Hmm.. Im gonna go try that right now.

Reznik Akime · « **Reply #42 on:** December 29, 2003, 11:43:00 AM »

Bah.. I got the orange light workin... which i assume is raincoat runnin like it should... but then.. i cant get the thing to telnet! It wont even ping and i followed the tuts on raincoat thats in the stickied topics.. but no go... All my antiviri and firewalls are down also... So whats the deal..? I know its not the cable cause in can ftp into evox and whatnot fine...

bradthemac · « **Reply #43 on:** December 29, 2003, 01:35:00 PM »

If you are using the 007 raincoat package that is on #xbins you have a raincoat version that is too old. I ran into problems using raincoat on an xbox that had a winbond chip on it. I checked and re-checked my solder points and nothing was wrong but i kept on getting an error message that was saying it could not erase or flash my chip. All you have to do is replace the file called raincoat in the 007 memory card directory and replace it with a newer version of raincoat (.501)

phikapjames · « **Reply #44 on:** December 29, 2003, 07:13:00 PM »

QUOTE

If you are using the 007 raincoat package that is on #xbins you have a raincoat version that is too old. I ran into problems using raincoat on an xbox that had a winbond chip on it. I checked and re-checked my solder points and nothing was wrong but i kept on getting an error message that was saying it could not erase or flash my chip. All you have to do is replace the file called raincoat in the 007 memory card directory and replace it with a newer version of raincoat (.501)

I just did a 1.5 with the winbond chip using the 007_tsop_flash_kit_1_0_alpha6 that is on xbins and it worked just fine without needing any replacement files or a configuration file (besides just needing a bios.bin added). Just a note that I used all three soldering points (always works the best for me that way).

QUOTE

yeah, 0x0900 means the chip isnt write enabled

This is partially wrong. If you try flashing the winbond chip using evox when there is no bios configuration for the winbond chip in the evox.ini then it will display this. It is still correct though that even after you add the bios configuration for the winbond chip, evox will NOT be able to flash it and just freeze.

Author Topic: 1.5 And 1.3 Winbond W49f020t-90b (Read 159 times)